![]() |
![]() |
Introduction
WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings
WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication.
It is widely used in injection and extrusion sheet applications. Suitable for ABS AS and PC materials.
It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.
It meets the Europe BPA Standard (EU)2024/3190.
Why food-contact black masterbatch now has a deadline
Since 20 January 2025, Commission Regulation (EU) 2024/3190 has banned bisphenol A in the manufacture of food contact materials. That covers plastics, coatings, adhesives, rubbers, printing inks and ion-exchange resins.
Most single-use and repeat-use articles have until 20 July 2026 under the current transitional periods. Professional food production equipment has a later date.
Enforcement guidance sets a detection limit of 1 µg/kg, and a Declaration of Compliance has to travel with the material at every stage of the supply chain.
For appliance manufacturers, BPA-free colouring is no longer a preference. It is a purchasing condition, and odour sits right behind it.
LFGB stands out among food-contact frameworks because it requires an organoleptic test.
Trained assessors check whether a material passes any smell or taste into the food simulant it has been in contact with.
WMB56 is formulated against both requirements at once.
Technical Parameter
| Carbon Content | 25%±1.5 |
| Carrier | PE |
| MFI | 50-75 (g/ 10min(220℃ 5 kg) |
| Moisture | ≤0.1% |
| Dispersion | Excellent (≤ Level 2.5) |
| Compliance | RoHS,PAHs,REACH, BPA Free, EN71-3 |
| Application | Injection (Appliance Casing, Automotive Exterior parts), Extrusion sheet for building material |
| Dosage Advice | Injection: 0.8–2.0% Extrusion: 1.0–4.0% |
| OEM | Accpeted |
● Low odour, low volatile release. For enclosed appliance interiors and for parts sitting close to food or drinking water. In those positions a smell transfer is a rejection risk, not a cosmetic one.
● High jetness at low dosage. A deep, consistent black from 0.8–2.0% addition in injection moulding, so the colour costs less per part than a general-purpose grade.
● Dispersion rated ≤ Level 2.5. On the finished part that shows up as an even gloss, with no black spots, streaks or surface bloom.
● Formulated for ABS, AS and PC. The carrier system is matched to engineering resins, so mechanical properties and surface finish hold up at the recommended addition rates.
● Stable in both injection moulding and extrusion. It performs in the temperature windows used for styrenic and polycarbonate parts, and in extruded sheet.
● Made on a dedicated food-grade line. The facility reserved for food-grade and BPA-sensitive production keeps cross-contamination out of the batch.
Applications
|
Application Area |
Typical Parts |
Base Resin |
|
Small kitchen appliances |
Coffee machine housings, blender and mixer bodies, water dispenser panels, air fryer casings |
ABS, ABS/PC |
|
Food-contact components |
Lids, trays, inner liners, dosing and dispensing parts |
ABS, AS, PC |
|
Appliance exteriors |
Control panels, decorative trims, visible housings |
ABS, AS |
|
Automotive parts |
Exterior and interior trim components |
ABS |
|
Extruded sheet |
Building material sheet |
PE |
Typical applications are given for reference. Please confirm suitability against your own resin grade and process conditions.
Is WMB56 BPA-free?
Yes. WMB56 uses no bisphenol A. It supports compliance with Commission Regulation (EU) 2024/3190, which has banned BPA in EU food contact materials since 20 January 2025.
Contact us for the Declaration of Compliance you need for your article documentation.
Yes. It is designed for ABS, AS and PC as well as polyolefins. Typical addition rates are 0.8–2.0% for injection moulding and 1.0–4.0% for extruded sheet.
Will it affect the mechanical properties of my parts?
At the recommended dosage the effect on the base resin is minimal. As with any masterbatch, a short trial on your own equipment with your own resin grade is the reliable way to confirm it.
WMB56 is a food-contact grade material. Final compliance depends on the finished article as a whole, including the base resin, other additives and processing conditions, so the complete formulation should be checked against the applicable regulation.
Low odour, which suits enclosed appliance interiors and food-adjacent parts. LFGB compliance includes an organoleptic assessment of odour and taste transfer, and the test documentation is available on request.
Send us your resin grade, target application and estimated annual volume. We will recommend the right dosage and supply the compliance documents you need.
Contact us for a sample and quotation → /contact-us
The technical values shown are typical results and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.
Packing and Storage
25kg/bag, PE bag or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.
![]() |
Introduction
WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings
WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication.
It is widely used in injection and extrusion sheet applications. Suitable for ABS AS and PC materials.
It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.
It meets the Europe BPA Standard (EU)2024/3190.
Why food-contact black masterbatch now has a deadline
Since 20 January 2025, Commission Regulation (EU) 2024/3190 has banned bisphenol A in the manufacture of food contact materials. That covers plastics, coatings, adhesives, rubbers, printing inks and ion-exchange resins.
Most single-use and repeat-use articles have until 20 July 2026 under the current transitional periods. Professional food production equipment has a later date.
Enforcement guidance sets a detection limit of 1 µg/kg, and a Declaration of Compliance has to travel with the material at every stage of the supply chain.
For appliance manufacturers, BPA-free colouring is no longer a preference. It is a purchasing condition, and odour sits right behind it.
LFGB stands out among food-contact frameworks because it requires an organoleptic test.
Trained assessors check whether a material passes any smell or taste into the food simulant it has been in contact with.
WMB56 is formulated against both requirements at once.
Technical Parameter
| Carbon Content | 25%±1.5 |
| Carrier | PE |
| MFI | 50-75 (g/ 10min(220℃ 5 kg) |
| Moisture | ≤0.1% |
| Dispersion | Excellent (≤ Level 2.5) |
| Compliance | RoHS,PAHs,REACH, BPA Free, EN71-3 |
| Application | Injection (Appliance Casing, Automotive Exterior parts), Extrusion sheet for building material |
| Dosage Advice | Injection: 0.8–2.0% Extrusion: 1.0–4.0% |
| OEM | Accpeted |
● Low odour, low volatile release. For enclosed appliance interiors and for parts sitting close to food or drinking water. In those positions a smell transfer is a rejection risk, not a cosmetic one.
● High jetness at low dosage. A deep, consistent black from 0.8–2.0% addition in injection moulding, so the colour costs less per part than a general-purpose grade.
● Dispersion rated ≤ Level 2.5. On the finished part that shows up as an even gloss, with no black spots, streaks or surface bloom.
● Formulated for ABS, AS and PC. The carrier system is matched to engineering resins, so mechanical properties and surface finish hold up at the recommended addition rates.
● Stable in both injection moulding and extrusion. It performs in the temperature windows used for styrenic and polycarbonate parts, and in extruded sheet.
● Made on a dedicated food-grade line. The facility reserved for food-grade and BPA-sensitive production keeps cross-contamination out of the batch.
Applications
|
Application Area |
Typical Parts |
Base Resin |
|
Small kitchen appliances |
Coffee machine housings, blender and mixer bodies, water dispenser panels, air fryer casings |
ABS, ABS/PC |
|
Food-contact components |
Lids, trays, inner liners, dosing and dispensing parts |
ABS, AS, PC |
|
Appliance exteriors |
Control panels, decorative trims, visible housings |
ABS, AS |
|
Automotive parts |
Exterior and interior trim components |
ABS |
|
Extruded sheet |
Building material sheet |
PE |
Typical applications are given for reference. Please confirm suitability against your own resin grade and process conditions.
Frequently asked questions
Is WMB56 BPA-free?
Yes. WMB56 uses no bisphenol A. It supports compliance with Commission Regulation (EU) 2024/3190, which has banned BPA in EU food contact materials since 20 January 2025.
Contact us for the Declaration of Compliance you need for your article documentation.
Yes. It is designed for ABS, AS and PC as well as polyolefins. Typical addition rates are 0.8–2.0% for injection moulding and 1.0–4.0% for extruded sheet.
Will it affect the mechanical properties of my parts?
At the recommended dosage the effect on the base resin is minimal. As with any masterbatch, a short trial on your own equipment with your own resin grade is the reliable way to confirm it.
WMB56 is a food-contact grade material. Final compliance depends on the finished article as a whole, including the base resin, other additives and processing conditions, so the complete formulation should be checked against the applicable regulation.
Low odour, which suits enclosed appliance interiors and food-adjacent parts. LFGB compliance includes an organoleptic assessment of odour and taste transfer, and the test documentation is available on request.
Send us your resin grade, target application and estimated annual volume. We will recommend the right dosage and supply the compliance documents you need.
Contact us for a sample and quotation → /contact-us
The technical values shown are typical results and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.
Packing and Storage
25kg/bag, PE bag or Composite Paper bag
Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.
Note
The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.


Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...