logo

SEARCH WHAT YOU WANT
English
  • English
  • Español
  • Русский
  • 日本語
  • عربي

Structure-Enhanced PC Black Masterbatch WM6245


Introduction

WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in  extrusion and high glossy injection applications. Suitable for PC ABS/PC materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Why Polycarbonate Needs Its Own Black Masterbatch

PC is not a polymer you can treat like PP. It runs hot, it pulls moisture out of the air, and its ester linkages break down by hydrolysis whenever water is around.

Drop a universal PE or PP grade into the hopper and three things go wrong at the same time.

The carrier and the base resin do not want to sit together. Polyolefins are thermodynamically incompatible with PC, so they phase-separate.

On the surface you see streaking, flow marks and stress cracking. Inside the part the impact strength drops, and that is the one you only find out about later.

Then comes heat. A polyolefin carrier starts to decompose below PC's processing window, which shows up as carbonised streaks, black spots and extra VOCs off the machine.

Dispersion is the third one. Any agglomerate that survives compounding will read as a speck, and thin-wall or translucent parts have nowhere to hide it.

 

This is why a black masterbatch for PC/ABS has to be built differently. WM6245 uses a PC carrier with an MFI of 35–50 g/10 min (300 °C / 2.16 kg), which is high on purpose.

The masterbatch melts before the base resin does, so it moves through the melt and takes the pigment with it.

 

Technical Parameter 

Carbon Content 6%±1.5
Carrier PC
MFI 35-50(g/ 10min(300℃ 2. 16 kg)
Moisture ≤0.3%
Compliance RoHS ,PAHs
Application High glossy Injection,  Extrusion sheet
Dosage Advice Injection: 0.8–2.0%  
OEM Accpeted

 

Key Properties

  • PC carrier, so it bonds with PC and PC/ABS instead of sitting inside it as a separate phase. No delamination.
  • Pre-dispersed carbon black, giving full jetness and tinting strength at low dosage.
  • Holds up across the whole PC processing window, 280–320 °C.
  • No specks, streaks or flow lines on high-gloss surfaces.
  • Little to no effect on the physical properties of the finished part.
  • Cylindrical pellets cut to a consistent length and diameter, which keeps feeding and dosing steady on the machine.
  • Runs in high-gloss injection moulding and in extrusion sheet.
  • RoHS and PAHs compliant.

 

Applications

Application Why WM6245 fits
High-gloss injection-moulded parts Pre-dispersed carbon black gives a streak-free surface at 0.8-2.0%
PC/ABS blends The PC carrier keeps the alloy compatible, so no phase separation
Extruded PC sheet andprofiles Stable MFI holds barrel pressure and wall thickness steady
Electrical and electronic housings  Stable MFI holds barrel pressure and wall thickness steady
Automotive interior and exterior trim Takes 280-320°C moulding without carbonised streaks
LED covers and lighting components  Colour holds through high-temperature processing
Appliance shells and handles High gloss and no surface defects

 

Why Jolink Tech

Jolink Tech has been making masterbatch for 30 years.

The production base covers 35,000 m², capacity runs past 30,000 tons a year, and there are 12 technicians in R&D with more than 40 patents behind the formulations.

Products ship to over 20 countries and pass RoHS, REACH, PAHs, FDA and BPA.

 

WM6245 comes with RoHS and PAHs documentation. If the standard grade is not the right fit, we accept OEM formulations, and carbon black loading, carrier MFI and jetness level can all be adjusted to your specification.

 

FAQ

 

Is WM6245 compatible with PC/ABS? Yes, and with plain PC too. The carrier is polycarbonate rather than a polyolefin, so there is no phase separation and no loss of impact strength.

Do I need to dry the masterbatch before use? You do. PC degrades hydrolytically, so dry the masterbatch and the base resin together at 120 °C for 3–4 hours and keep moisture below 0.02%.

What dosage should I use? 0.8–2.0% for injection moulding. Start at the low end and work up until the part reads as black as your application needs.

Can it be used for extrusion? Yes. Extrusion sheet is one of the main applications, alongside high-gloss injection moulding. Start the trial at 1.0–2.5% and adjust from there.

Will it change the properties of my finished part? The formulation is built to keep that effect as small as possible. It comes down to the carrier being compatible with the PC matrix.

Is it RoHS and PAHs compliant? Yes, and the compliance documentation is available on request.

Can you produce a custom grade? We can. OEM formulations are accepted, and carbon black loading, carrier MFI and shade can be adjusted to match your process.

Will it work on parts that need laser marking? Carbon-black pigmented PC and PC/ABS can normally be laser marked.

How much contrast you get depends on the laser system, the pigment level and the base formulation, so send us your process details and we will tell you which grade to run.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.

 

Introduction

WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in  extrusion and high glossy injection applications. Suitable for PC ABS/PC materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Why Polycarbonate Needs Its Own Black Masterbatch

PC is not a polymer you can treat like PP. It runs hot, it pulls moisture out of the air, and its ester linkages break down by hydrolysis whenever water is around.

Drop a universal PE or PP grade into the hopper and three things go wrong at the same time.

The carrier and the base resin do not want to sit together. Polyolefins are thermodynamically incompatible with PC, so they phase-separate.

On the surface you see streaking, flow marks and stress cracking. Inside the part the impact strength drops, and that is the one you only find out about later.

Then comes heat. A polyolefin carrier starts to decompose below PC's processing window, which shows up as carbonised streaks, black spots and extra VOCs off the machine.

Dispersion is the third one. Any agglomerate that survives compounding will read as a speck, and thin-wall or translucent parts have nowhere to hide it.

 

This is why a black masterbatch for PC/ABS has to be built differently. WM6245 uses a PC carrier with an MFI of 35–50 g/10 min (300 °C / 2.16 kg), which is high on purpose.

The masterbatch melts before the base resin does, so it moves through the melt and takes the pigment with it.

 

Technical Parameter 

Carbon Content 6%±1.5
Carrier PC
MFI 35-50(g/ 10min(300℃ 2. 16 kg)
Moisture ≤0.3%
Compliance RoHS ,PAHs
Application High glossy Injection,  Extrusion sheet
Dosage Advice Injection: 0.8–2.0%  
OEM Accpeted

 

Key Properties

  • PC carrier, so it bonds with PC and PC/ABS instead of sitting inside it as a separate phase. No delamination.
  • Pre-dispersed carbon black, giving full jetness and tinting strength at low dosage.
  • Holds up across the whole PC processing window, 280–320 °C.
  • No specks, streaks or flow lines on high-gloss surfaces.
  • Little to no effect on the physical properties of the finished part.
  • Cylindrical pellets cut to a consistent length and diameter, which keeps feeding and dosing steady on the machine.
  • Runs in high-gloss injection moulding and in extrusion sheet.

 

  • RoHS and PAHs compliant.

 

Applications

Application Why WM6245 fits
High-gloss injection-moulded parts Pre-dispersed carbon black gives a streak-free surface at 0.8-2.0%
PC/ABS blends The PC carrier keeps the alloy compatible, so no phase separation
Extruded PC sheet andprofiles Stable MFI holds barrel pressure and wall thickness steady
Electrical and electronic housings  Stable MFI holds barrel pressure and wall thickness steady
Automotive interior and exterior trim Takes 280-320°C moulding without carbonised streaks
LED covers and lighting components  Colour holds through high-temperature processing
Appliance shells and handles High gloss and no surface defects

 

Why Jolink Tech

Jolink Tech has been making masterbatch for 30 years. The production base covers 35,000 m², capacity runs past 30,000 tons a year, and there are 12 technicians in R&D with more than 40 patents behind the formulations.

Products ship to over 20 countries and pass RoHS, REACH, PAHs, FDA and BPA.

 

WM6245 comes with RoHS and PAHs documentation. If the standard grade is not the right fit, we accept OEM formulations, and carbon black loading, carrier MFI and jetness level can all be adjusted to your specification.

 

FAQ

 

Is WM6245 compatible with PC/ABS? Yes, and with plain PC too. The carrier is polycarbonate rather than a polyolefin, so there is no phase separation and no loss of impact strength.

Do I need to dry the masterbatch before use? You do. PC degrades hydrolytically, so dry the masterbatch and the base resin together at 120 °C for 3–4 hours and keep moisture below 0.02%.

What dosage should I use? 0.8–2.0% for injection moulding. Start at the low end and work up until the part reads as black as your application needs.

Can it be used for extrusion? Yes. Extrusion sheet is one of the main applications, alongside high-gloss injection moulding. Start the trial at 1.0–2.5% and adjust from there.

Will it change the properties of my finished part? The formulation is built to keep that effect as small as possible. It comes down to the carrier being compatible with the PC matrix.

Is it RoHS and PAHs compliant? Yes, and the compliance documentation is available on request.

Can you produce a custom grade? We can. OEM formulations are accepted, and carbon black loading, carrier MFI and shade can be adjusted to match your process.

 

Will it work on parts that need laser marking? Carbon-black pigmented PC and PC/ABS can normally be laser marked.

How much contrast you get depends on the laser system, the pigment level and the base formulation, so send us your process details and we will tell you which grade to run.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.


Previous: No more data

Related Products
black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

black-masterbatch-blown-film-extrusion-1010C

Environmentally Friendly Black Masterbatch WM101-WM101

Environmentally Friendly Black Masterbatch WM101

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

black masterbatch for general use

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E-WM8E

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Universal Courier bag Extrusion Black Masterbatch WM2ADM-WM2ADM

Universal Courier bag Extrusion Black Masterbatch WM2ADM

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1-WMULCH-1

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

black masterbatch

High Concentration Carrier-Free Black Masterbatch WMB34-WMB34

High Concentration Carrier-Free Black Masterbatch WMB34

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

black masterbatch

Strong And High Pigment Black Masterbatch WM913-WM913

Strong And High Pigment Black Masterbatch WM913

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

black masterbatch for injection

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11-WMEG11

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

black masterbatch for automotive parts

BPA Free & LFGB Approved food grade Black Masterbatch WMB56-WMB56

BPA Free & LFGB Approved food grade Black Masterbatch WMB56

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

black-masterbatch-PP-superior-blueblack-modified-engineering-compounding-TKB2025007(8)-5D

Strong And High Pigment PP Black Masterbatch WM785D-WM785D

Strong And High Pigment PP Black Masterbatch WM785D

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

black-masterbatch-home-appliance-casing-BPA-free-lfgb-approved-2016HC

Injection Molding Reinforced Black Masterbatch WM16H (UN2014) -WM16H

Injection Molding Reinforced Black Masterbatch WM16H (UN2014)

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

black masterbatch high concentration

Structure-Enhanced SAN Black Masterbatch WM2A-WM2A

Structure-Enhanced SAN Black Masterbatch WM2A

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

black-masterbatch-PS-panel-extrusion-KB2506026

Structure-Enhanced PS Black Masterbatch WM626-WM626

Structure-Enhanced PS Black Masterbatch WM626

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Get Your Free Sample Now
Submit this form and our sales representative will contact you soon.
*Name
Phone
*Email
Company
*Message