logo

SEARCH WHAT YOU WANT
English
  • English
  • Español
  • Русский
  • 日本語
  • عربي

Environmentally Resistant Black Masterbatch WM3F


Introduction

WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Technical Parameter 

Carbon Content  45%
Carrier PE
MFI 5-15 (g/ 10min(190℃ 10kg)
Moisture ≤0.15%
Dispersion Excellent (≤ Level 3) 
Compliance RoHS
Application Water supply pipe/ Drip tape/Corrugated Pipes  Blow film (courier bags)
Dosage Advice Film blowing: 4.0–8.0%   Extrusion: 1.0–4.0%
OEM Accepted

 

Why WM3F Is Specified for Water Supply Pipe

 Dispersion is specified as a number, not an adjective

A masterbatch can look perfectly black and still fail a pressure pipe. What decides whether the carbon black protects the wall or damages it is dispersion.

WM3F is specified at ≤ Level 2.5 on the ISO 18553 scale, inside the grade 3 limit that ISO 4427 and EN 12201 set for black PE compounds.

Agglomerates that never dispersed act as stress concentration points, and under sustained internal pressure they are where slow crack growth starts.

That is why we publish a measured grade instead of just saying the dispersion is good.

Moisture stays below 0.15%

Water vapor in a masterbatch flashes to steam inside the extruder barrel, and you end up with micro-voids, pinholes and silver streaks in the pipe wall.

Those defects sit right in the load path of a pressurized pipe.

WM3F ships at ≤0.15% moisture in sealed 25 kg bags, well below the ≤0.50% ceiling quoted on most pipe-grade datasheets, and under normal storage it needs no pre-drying.

Pre-dispersed carbon black for single-screw extruders

Pipe lines are single-screw extruders. Residence time is short and mixing intensity is limited, so most of the dispersion work has to be finished before the material reaches your hopper.

Carbon black stays in colloidal form even when molten, which means what happens at the die is largely decided upstream.

WM3F's carbon black is pre-dispersed, then compounded with the carrier by plastication. The blackness and tinting power come from the material, not from hoping your screw finishes the job.

One grade covers pipe, drip tape, corrugated pipe and film

WM3F runs in both PE and PP.

A converter making water supply pipe, drip irrigation tape, corrugated pipe and blown film can keep one grade in stock and change the dosage per product, instead of swapping material between runs.

Dosage and Carbon Black Content in the Finished Pipe

ISO 4427 and EN 12201 require black PE water pipe compounds to contain 2.0–2.5% carbon black by mass, tested to ISO 6964, with a dispersion grade of 3 or better.

ISO 8779 applies the same carbon black window to PE irrigation pipe. How much WM3F you need depends on how much carbon black your base resin already carries.

 

WM3F dosage in the compound

Carbon black introduced into the pipe wall

1.0%

0.45%

2.0%

0.90%

3.0%

1.35%

4.0%

1.80%

4.5%

2.03%

5.0%

2.25%

5.5%

2.48%

 

Calculated at 45% carbon black, the nominal mid-point of the 44–46.5% specification.

Between 1.0% and 4.0% extrusion dosage, WM3F colors the pipe and gives partial UV protection.

That is the right level when the base resin already brings part of the carbon black load. Where a natural, carbon-black-free resin has to reach the 2.0–2.5% specification, WM3F goes in at roughly 4.5–5.6%.

Carbon black above about 3% by mass brings no further UV benefit and starts raising the risk of agglomeration and lost impact strength.

More masterbatch is not more protection. OIT (ISO 11357-6) is set mainly by the antioxidant package in your base compound, not by the masterbatch.

Send us your base resin datasheet and the standard you are working to and we will work out the exact addition rate for your line.

 

How Carbon Black Protects a PE Pipe Wall from UV Degradation

Carbon black absorbs UV-A and UV-B across the 280–400 nm band and dissipates the energy as heat.

Intercept the photons before they reach the polymer chain and you avoid the free-radical chain scission behind surface chalking, embrittlement and lost elongation.

Protection does not stop at the surface. Functional groups on the carbon black particles intercept free radicals that form beneath the fully shielded outer layer,

which extends protection into the sub-surface zone instead of leaving it all to a single absorbing skin.

Then there is heat. Pipe stored outdoors in direct sun gets far hotter than ambient air,

and carbon black's thermal absorption plus its radical scavenging moderate photo-oxidative and thermal degradation at the same time.

That matters during the weeks or months a pipe spends in an open yard before installation.

Buried pipe still sits above ground for a long stretch before backfilling, so UV shielding is specified for the whole service life, not just the sections that stay exposed.

 

Processing WM3F in Pipe Extrusion

Process parameter

Guidance

Barrel temperature

190–220 °C, the usual HDPE pipe compound window

Feeding

Dry-blend at the hopper. A gravimetric feeder holds dosage steady across long runs and shift changes

Dosage at the 2.25% carbon black target

50 kg WM3F per 1,000 kg compound, which puts 22.5 kg carbon black and 27.5 kg PE carrier into every tonne of pipe

Screen pack and die

No die changes needed. Pre-dispersed carbon black passes standard pipe screen packs without pressure instability

Pre-drying

Not required as delivered (≤0.15% moisture). If opened bags have sat above 70% RH for a long period, pre-dry at 70 °C for 2 hours

Color verification

Cut a cross-section chip at the start of each run and check the black is uniform through the wall before you commit to full production

Purging

Standard PE purge. The PE carrier clears the screw and die within a normal pipe-length purge

 
Compliance, Quality and Supply

WM3F is RoHS, REACH and PAHs compliant. The datasheet, safety data sheet, batch test data and compliance declarations are issued with your order on request.

Jolink has manufactured carbon black masterbatch for 30 years from a 35,000 m² plant with 30,000 tonnes of annual capacity, exporting to more than 20 countries.

The product range is covered by 40+ patents. WM3F is classified under HS code 32064990.00.

Packaging is 25 kg PE or composite paper bags, palletized for export. Store sealed in a dry, cool warehouse away from direct sunlight, and reseal opened bags to keep moisture out.

 

FAQ: Black Masterbatch for Water Supply Pipe

How much WM3F is needed to reach 2.0–2.5% carbon black in an HDPE water pipe?

At 45% carbon black content, WM3F goes in at approximately 4.5–5.6% when the base resin contains no carbon black of its own.

If your PE 80 or PE 100 base compound is already partly black, subtract its carbon black contribution first.

Send us the base resin datasheet and the standard you are working to (ISO 4427, EN 12201, ISO 8779 or a national equivalent) and we will send back the exact addition rate.

Does WM3F meet the dispersion requirement of ISO 4427 and EN 12201?

Yes. Both standards require black PE compounds to reach a dispersion grade of 3 or better on the ISO 18553 scale, where a lower number means better dispersion.

WM3F is specified at ≤ Level 2.5. Keep in mind that the requirement applies to the finished compound, so you should also verify dispersion on your extruded pipe through your own routine testing.

Our masterbatch dispersion data is there to support your incoming inspection.

Can WM3F be used for PP pipe and drip irrigation tape as well as HDPE?

Yes. WM3F runs in PE and PP and is used in water supply pipe, drip irrigation tape, corrugated pipe and blown film.

Recommended dosage is 4.0–8.0% in blown film and 1.0–4.0% in pipe and profile extrusion, adjusted to your carbon black target.

The datasheet quotes melt flow index at 190 °C / 10 kg. How should I read that figure?

Melt flow index only compares like for like, at the same temperature and load. WM3F is quoted under ISO 1133 Condition F (190 °C / 10 kg).

The same polymer measured at 190 °C / 21.6 kg (Condition G) or 190 °C / 2.16 kg (Condition D) gives a very different number, because the heavier load drives faster flow.

Confirm the test condition before you compare two grades. If your incoming inspection uses a different condition, tell us which one and we will send matching test data.

Do you accept OEM orders and custom specifications?

Yes. Carbon black content, carrier resin and additive package are set per grade. Tell us your target pipe grade and the standard you are working to and we will confirm what is available.

OEM and private-label packaging are accepted.

Request a Sample or Dosage Calculation

Send your base resin datasheet, the pipe standard you are working to and your target carbon black content.

We will reply with a recommended WM3F addition rate, the technical data sheet and a sample for your trial run.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.

Introduction

WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Technical Parameter 

Carbon Content  45%
Carrier PE
MFI 5-15 (g/ 10min(190℃ 10kg)
Moisture ≤0.15%
Dispersion Excellent (≤ Level 3) 
Compliance RoHS
Application Water supply pipe/ Drip tape/Corrugated Pipes  Blow film (courier bags)
Dosage Advice Film blowing: 4.0–8.0%   Extrusion: 1.0–4.0%
OEM Accepted

 

Why WM3F Is Specified for Water Supply Pipe

 Dispersion is specified as a number, not an adjective

A masterbatch can look perfectly black and still fail a pressure pipe. What decides whether the carbon black protects the wall or damages it is dispersion.

WM3F is specified at ≤ Level 2.5 on the ISO 18553 scale, inside the grade 3 limit that ISO 4427 and EN 12201 set for black PE compounds.

Agglomerates that never dispersed act as stress concentration points, and under sustained internal pressure they are where slow crack growth starts.

That is why we publish a measured grade instead of just saying the dispersion is good.

Moisture stays below 0.15%

Water vapor in a masterbatch flashes to steam inside the extruder barrel, and you end up with micro-voids, pinholes and silver streaks in the pipe wall.

Those defects sit right in the load path of a pressurized pipe.

WM3F ships at ≤0.15% moisture in sealed 25 kg bags, well below the ≤0.50% ceiling quoted on most pipe-grade datasheets, and under normal storage it needs no pre-drying.

Pre-dispersed carbon black for single-screw extruders

Pipe lines are single-screw extruders. Residence time is short and mixing intensity is limited, so most of the dispersion work has to be finished before the material reaches your hopper.

Carbon black stays in colloidal form even when molten, which means what happens at the die is largely decided upstream.

WM3F's carbon black is pre-dispersed, then compounded with the carrier by plastication. The blackness and tinting power come from the material, not from hoping your screw finishes the job.

One grade covers pipe, drip tape, corrugated pipe and film

WM3F runs in both PE and PP.

A converter making water supply pipe, drip irrigation tape, corrugated pipe and blown film can keep one grade in stock and change the dosage per product, instead of swapping material between runs.

Dosage and Carbon Black Content in the Finished Pipe

ISO 4427 and EN 12201 require black PE water pipe compounds to contain 2.0–2.5% carbon black by mass, tested to ISO 6964, with a dispersion grade of 3 or better.

ISO 8779 applies the same carbon black window to PE irrigation pipe. How much WM3F you need depends on how much carbon black your base resin already carries.

 

WM3F dosage in the compound

Carbon black introduced into the pipe wall

1.0%

0.45%

2.0%

0.90%

3.0%

1.35%

4.0%

1.80%

4.5%

2.03%

5.0%

2.25%

5.5%

2.48%

 

Calculated at 45% carbon black, the nominal mid-point of the 44–46.5% specification.

Between 1.0% and 4.0% extrusion dosage, WM3F colors the pipe and gives partial UV protection.

That is the right level when the base resin already brings part of the carbon black load. Where a natural, carbon-black-free resin has to reach the 2.0–2.5% specification, WM3F goes in at roughly 4.5–5.6%.

Carbon black above about 3% by mass brings no further UV benefit and starts raising the risk of agglomeration and lost impact strength.

More masterbatch is not more protection. OIT (ISO 11357-6) is set mainly by the antioxidant package in your base compound, not by the masterbatch.

Send us your base resin datasheet and the standard you are working to and we will work out the exact addition rate for your line.

 

How Carbon Black Protects a PE Pipe Wall from UV Degradation

Carbon black absorbs UV-A and UV-B across the 280–400 nm band and dissipates the energy as heat.

Intercept the photons before they reach the polymer chain and you avoid the free-radical chain scission behind surface chalking, embrittlement and lost elongation.

Protection does not stop at the surface. Functional groups on the carbon black particles intercept free radicals that form beneath the fully shielded outer layer,

which extends protection into the sub-surface zone instead of leaving it all to a single absorbing skin.

Then there is heat. Pipe stored outdoors in direct sun gets far hotter than ambient air,

and carbon black's thermal absorption plus its radical scavenging moderate photo-oxidative and thermal degradation at the same time.

That matters during the weeks or months a pipe spends in an open yard before installation.

Buried pipe still sits above ground for a long stretch before backfilling, so UV shielding is specified for the whole service life, not just the sections that stay exposed.

 

Processing WM3F in Pipe Extrusion

Process parameter

Guidance

Barrel temperature

190–220 °C, the usual HDPE pipe compound window

Feeding

Dry-blend at the hopper. A gravimetric feeder holds dosage steady across long runs and shift changes

Dosage at the 2.25% carbon black target

50 kg WM3F per 1,000 kg compound, which puts 22.5 kg carbon black and 27.5 kg PE carrier into every tonne of pipe

Screen pack and die

No die changes needed. Pre-dispersed carbon black passes standard pipe screen packs without pressure instability

Pre-drying

Not required as delivered (≤0.15% moisture). If opened bags have sat above 70% RH for a long period, pre-dry at 70 °C for 2 hours

Color verification

Cut a cross-section chip at the start of each run and check the black is uniform through the wall before you commit to full production

Purging

Standard PE purge. The PE carrier clears the screw and die within a normal pipe-length purge

 
Compliance, Quality and Supply

WM3F is RoHS, REACH and PAHs compliant. The datasheet, safety data sheet, batch test data and compliance declarations are issued with your order on request.

Jolink has manufactured carbon black masterbatch for 30 years from a 35,000 m² plant with 30,000 tonnes of annual capacity, exporting to more than 20 countries.

The product range is covered by 40+ patents. WM3F is classified under HS code 32064990.00.

Packaging is 25 kg PE or composite paper bags, palletized for export. Store sealed in a dry, cool warehouse away from direct sunlight, and reseal opened bags to keep moisture out.

 

FAQ: Black Masterbatch for Water Supply Pipe

How much WM3F is needed to reach 2.0–2.5% carbon black in an HDPE water pipe?

At 45% carbon black content, WM3F goes in at approximately 4.5–5.6% when the base resin contains no carbon black of its own.

If your PE 80 or PE 100 base compound is already partly black, subtract its carbon black contribution first.

Send us the base resin datasheet and the standard you are working to (ISO 4427, EN 12201, ISO 8779 or a national equivalent) and we will send back the exact addition rate.

Does WM3F meet the dispersion requirement of ISO 4427 and EN 12201?

Yes. Both standards require black PE compounds to reach a dispersion grade of 3 or better on the ISO 18553 scale, where a lower number means better dispersion.

WM3F is specified at ≤ Level 2.5. Keep in mind that the requirement applies to the finished compound, so you should also verify dispersion on your extruded pipe through your own routine testing.

Our masterbatch dispersion data is there to support your incoming inspection.

Can WM3F be used for PP pipe and drip irrigation tape as well as HDPE?

Yes. WM3F runs in PE and PP and is used in water supply pipe, drip irrigation tape, corrugated pipe and blown film.

Recommended dosage is 4.0–8.0% in blown film and 1.0–4.0% in pipe and profile extrusion, adjusted to your carbon black target.

The datasheet quotes melt flow index at 190 °C / 10 kg. How should I read that figure?

Melt flow index only compares like for like, at the same temperature and load. WM3F is quoted under ISO 1133 Condition F (190 °C / 10 kg).

The same polymer measured at 190 °C / 21.6 kg (Condition G) or 190 °C / 2.16 kg (Condition D) gives a very different number, because the heavier load drives faster flow.

Confirm the test condition before you compare two grades. If your incoming inspection uses a different condition, tell us which one and we will send matching test data.

Do you accept OEM orders and custom specifications?

Yes. Carbon black content, carrier resin and additive package are set per grade. Tell us your target pipe grade and the standard you are working to and we will confirm what is available.

OEM and private-label packaging are accepted.

Request a Sample or Dosage Calculation

Send your base resin datasheet, the pipe standard you are working to and your target carbon black content.

We will reply with a recommended WM3F addition rate, the technical data sheet and a sample for your trial run.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.


Previous: No more data

Related Products
black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

black-masterbatch-blown-film-extrusion-1010C

Environmentally Friendly Black Masterbatch WM101-WM101

Environmentally Friendly Black Masterbatch WM101

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

black masterbatch for general use

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E-WM8E

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Universal Courier bag Extrusion Black Masterbatch WM2ADM-WM2ADM

Universal Courier bag Extrusion Black Masterbatch WM2ADM

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1-WMULCH-1

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

black masterbatch

High Concentration Carrier-Free Black Masterbatch WMB34-WMB34

High Concentration Carrier-Free Black Masterbatch WMB34

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

black masterbatch

Strong And High Pigment Black Masterbatch WM913-WM913

Strong And High Pigment Black Masterbatch WM913

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

black masterbatch for injection

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11-WMEG11

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

black masterbatch for automotive parts

BPA Free & LFGB Approved food grade Black Masterbatch WMB56-WMB56

BPA Free & LFGB Approved food grade Black Masterbatch WMB56

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

black-masterbatch-PP-superior-blueblack-modified-engineering-compounding-TKB2025007(8)-5D

Strong And High Pigment PP Black Masterbatch WM785D-WM785D

Strong And High Pigment PP Black Masterbatch WM785D

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

black-masterbatch-home-appliance-casing-BPA-free-lfgb-approved-2016HC

Injection Molding Reinforced Black Masterbatch WM16H (UN2014) -WM16H

Injection Molding Reinforced Black Masterbatch WM16H (UN2014)

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

black masterbatch high concentration

Structure-Enhanced SAN Black Masterbatch WM2A-WM2A

Structure-Enhanced SAN Black Masterbatch WM2A

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

black-masterbatch-PS-panel-extrusion-KB2506026

Structure-Enhanced PS Black Masterbatch WM626-WM626

Structure-Enhanced PS Black Masterbatch WM626

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Get Your Free Sample Now
Submit this form and our sales representative will contact you soon.
*Name
Phone
*Email
Company
*Message