logo

SEARCH WHAT YOU WANT
English
  • English
  • Español
  • Русский
  • 日本語
  • عربي

Universal Environmentally Resistant Black Masterbatch WM72


Introduction

WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Where WM72 goes

 

PE cable jacketing and sheathing

Jacketing is the hardest job WM72 does. The grade suits PE, MDPE, HDPE and LLDPE jacket layers on power, control and communication cable, and it also covers the black outer wall on conduit and duct.

A jacket is a thin wall running at speed, and anything that has not dispersed shows up on the surface within minutes.

Pre-dispersed carbon black and a PE carrier both help here. If you are looking at XLPE insulation rather than jacketing, tell us before you order.

That is a different job and it needs a different grade.

 

Pipe, corrugated profile and conduit

Drainage pipe, corrugated pipe and cable duct want what a jacket wants. Steady colour down a long run, and a clean surface.

Your target carbon black level sits close to a jacket's, so dose in the same 4–8% band and trim from there on your own line.

[Pipe extrusion grades →] /product/category/extruded-pipe

 

Blown film and bags

Courier bags, refuse sacks, mulch film and general packaging film run at 4–8%. Standard gauges hold full opacity at the low end of that range.

Go higher when the film is thin or the black has to be completely solid.

[Film grades →] /product/category/black-masterbatch-for-extruded-film

 

Injection moulded parts

PP and PE parts that need a clean black surface run at 0.8–2.0%. Crates, caps, fittings, housings are the usual cases.

At that level the tinting strength is high enough that you are paying for pigment rather than filler, and the part keeps the mechanical properties it was designed around.

 

Technical Parameter 

 

Carbon Content 36%±1.5
Carrier PE
MFI 5-15 (g/ 10min(190℃ 10kg)
Moisture ≤0.2%
Dispersion Excellent (≤ Level 3) 
Compliance RoHS
Application Blow film , Injection , Blow plastics
Dosage Advice Film blowing: 4.0–8.0%   Injection: 0.8–2.0% 
OEM Accpeted

 

Why it holds up

The difference between a good black masterbatch and a cheap one is rarely how much carbon black it carries. It is whether the pigment was separated before it went into the resin.

We wet and disperse the carbon black first, then compound it into the carrier.

Undispersed agglomerates are what cause the rough surface and the weak spots on a jacket wall, and dosing more masterbatch does not fix them.

[See how the compound is built →] /news/what-actually-happens-inside-a-twin-screw-extruder

 

Moisture stays under 0.2%. Every kilogram of water that reaches the die turns into steam, and steam in a thin PE wall leaves pinholes and a flat, uneven surface.

Keep the bag sealed once you open it. On a thick injection part, moisture is an annoyance. On a cable jacket, it is a reject.

Pellets are cut to a consistent size. Same length, same diameter, so they feed evenly and the carbon black level holds down the length of a run instead of drifting.

That consistency comes from holding the die-face cutting to one standard across the whole line, not just at the start of a batch.

[Why our pellets are so uniform →] /news/why-is-the-particle-size-of-our-black-masterbatch-so-uniform

 

The carrier matches the resin you already run.

WM72 sits on a PE carrier at 5–15 g/10 min MFI. On PE jacketing, pipe and film lines it melts inside the window you have already set,

so in most cases you dry-blend it at the hopper and leave your temperature profile alone.

 

It leaves the base resin largely as it found it. A filler-loaded or recycled carrier dilutes the base resin's mechanical profile.

WM72 carries dispersed pigment on a clean PE base rather than a heavy filler load, so the finished part barely changes.

 

Getting consistent results on the line

Dry the resin, not the masterbatch. Dry your base resin to its own datasheet, usually 70–90 °C for one to two hours on PE. Leave the masterbatch sealed until you charge the hopper.

 

Meter by weight. At 6–8% dosing, a gravimetric feeder holds the carbon black level steady along the run. Volumetric dosing drifts, and on a jacket you will see it as a colour swing.

 

Tumble blend long enough. Ten to fifteen minutes at low speed is usually enough to distribute the pellets evenly. Short blends are the most common cause of a batch that runs different from the last one.

 

Keep the profile where your base resin wants it. The carrier is already compatible, so extra heat and extra shear do not improve dispersion. They just start working on the resin. Most PE jacketing lines are happy between 180 and 220 °C.

 

Purge with base resin. A PE carrier purges out with PE. Run a short charge of virgin resin through rather than a chemical purge, and check the first metres before you commit to a long run.

 

 

Use the screen pack as a gauge. A 40–80 mesh pack tells you within minutes whether a batch is dispersing cleanly. If the pressure climbs faster than normal, stop and check the resin lot before you blame the masterbatch.

 

Compliance and documentation

This grade is declared RoHS. Across the wider range we work to RoHS, REACH, PAHs, FDA and BPA requirements, and we will confirm the status of a specific regulation for your market on request.

A certificate of analysis goes out with every batch, and the SDS and full TDS are available before you order. If your project names a standard,

send it over and we will tell you plainly whether WM72 meets it or whether you need a different grade.

 

Frequently asked questions

 

What dosage do I need for cable jacketing?

Most PE jacket specifications target 2.5% carbon black in the finished compound. WM72 carries 36%, so 2.5 ÷ 0.36 lands at about 7%.

That puts the practical working range at 6–8%, and you should confirm the exact figure on a trial run with your own resin.

Can I run it in PP as well as PE?

Yes, in both. That is what makes it a general-purpose grade. The carrier is PE, so on a PP line give the screw enough mixing length and check the surface on the first few metres.

How is dispersion graded?

We grade dispersion on a visual scale where a lower number is better, and WM72 is supplied at ≤3. Jacket specifications commonly call for ≤3 on a comparable scale.

If your project names a tighter figure, send it over and we will confirm before you commit to a trial.

Will it change the mechanical properties of my part?

The effect is small. The carrier is clean PE with the pigment already dispersed in it, so tensile strength and elongation of the base resin are largely retained. Confirm on your own formulation, as always.

Can I use it for XLPE or LV insulation?

No. Insulation is a different requirement. It needs controlled electrical properties and an additive package built for the crosslinking route you use. WM72 is for the jacket.

We supply insulation-grade compounds separately, so tell us what you are building.

Do you supply samples and OEM grades?

Yes to both. OEM is accepted: we can adjust carbon black loading and carrier to your specification, and we keep your formulation confidential. Samples ship with a certificate of analysis.

Packaging and storage

Supplied in 25 kg bags, PE or composite paper. Store dry, enclosed and out of direct sunlight. Reseal the bag after opening so the product stays dry.

Send us the part, the resin and the black you need

 

Tell us the jacket wall thickness, the base resin and your target carbon black level, and we will come back with a dosage and a sample.

If you already have a rejected batch from another supplier, send a photo with it.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.

 

Introduction

WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It features low dosage, high blackness, good brightness, excellent heat resistance, outstanding dispersibility and tinting power, and minimal impact on the physical properties of the final product.

 

Where WM72 goes

 

PE cable jacketing and sheathing

Jacketing is the hardest job WM72 does. The grade suits PE, MDPE, HDPE and LLDPE jacket layers on power, control and communication cable, and it also covers the black outer wall on conduit and duct.

A jacket is a thin wall running at speed, and anything that has not dispersed shows up on the surface within minutes.

Pre-dispersed carbon black and a PE carrier both help here. If you are looking at XLPE insulation rather than jacketing, tell us before you order.

That is a different job and it needs a different grade.

 

Pipe, corrugated profile and conduit

Drainage pipe, corrugated pipe and cable duct want what a jacket wants. Steady colour down a long run, and a clean surface.

Your target carbon black level sits close to a jacket's, so dose in the same 4–8% band and trim from there on your own line.

[Pipe extrusion grades →] /product/category/extruded-pipe

 

Blown film and bags

Courier bags, refuse sacks, mulch film and general packaging film run at 4–8%. Standard gauges hold full opacity at the low end of that range.

Go higher when the film is thin or the black has to be completely solid.

[Film grades →] /product/category/black-masterbatch-for-extruded-film

 

Injection moulded parts

 

PP and PE parts that need a clean black surface run at 0.8–2.0%. Crates, caps, fittings, housings are the usual cases.

At that level the tinting strength is high enough that you are paying for pigment rather than filler, and the part keeps the mechanical properties it was designed around.

 

Technical Parameter 

 

Carbon Content 36%±1.5
Carrier PE
MFI 5-15 (g/ 10min(190℃ 10kg)
Moisture ≤0.2%
Dispersion Excellent (≤ Level 3) 
Compliance RoHS
Application Blow film , Injection , Blow plastics
Dosage Advice Film blowing: 4.0–8.0%   Injection: 0.8–2.0% 
OEM Accpeted

 

Why it holds up

The difference between a good black masterbatch and a cheap one is rarely how much carbon black it carries. It is whether the pigment was separated before it went into the resin.

We wet and disperse the carbon black first, then compound it into the carrier.

Undispersed agglomerates are what cause the rough surface and the weak spots on a jacket wall, and dosing more masterbatch does not fix them.

[See how the compound is built →] /news/what-actually-happens-inside-a-twin-screw-extruder

 

Moisture stays under 0.2%. Every kilogram of water that reaches the die turns into steam, and steam in a thin PE wall leaves pinholes and a flat, uneven surface.

Keep the bag sealed once you open it. On a thick injection part, moisture is an annoyance. On a cable jacket, it is a reject.

Pellets are cut to a consistent size. Same length, same diameter, so they feed evenly and the carbon black level holds down the length of a run instead of drifting.

That consistency comes from holding the die-face cutting to one standard across the whole line, not just at the start of a batch.

[Why our pellets are so uniform →] /news/why-is-the-particle-size-of-our-black-masterbatch-so-uniform

 

The carrier matches the resin you already run.

WM72 sits on a PE carrier at 5–15 g/10 min MFI. On PE jacketing, pipe and film lines it melts inside the window you have already set,

so in most cases you dry-blend it at the hopper and leave your temperature profile alone.

 

It leaves the base resin largely as it found it. A filler-loaded or recycled carrier dilutes the base resin's mechanical profile.

WM72 carries dispersed pigment on a clean PE base rather than a heavy filler load, so the finished part barely changes.

 

Getting consistent results on the line

Dry the resin, not the masterbatch. Dry your base resin to its own datasheet, usually 70–90 °C for one to two hours on PE. Leave the masterbatch sealed until you charge the hopper.

 

Meter by weight. At 6–8% dosing, a gravimetric feeder holds the carbon black level steady along the run. Volumetric dosing drifts, and on a jacket you will see it as a colour swing.

 

Tumble blend long enough. Ten to fifteen minutes at low speed is usually enough to distribute the pellets evenly. Short blends are the most common cause of a batch that runs different from the last one.

 

Keep the profile where your base resin wants it. The carrier is already compatible, so extra heat and extra shear do not improve dispersion. They just start working on the resin. Most PE jacketing lines are happy between 180 and 220 °C.

 

Purge with base resin. A PE carrier purges out with PE. Run a short charge of virgin resin through rather than a chemical purge, and check the first metres before you commit to a long run.

 

 

Use the screen pack as a gauge. A 40–80 mesh pack tells you within minutes whether a batch is dispersing cleanly. If the pressure climbs faster than normal, stop and check the resin lot before you blame the masterbatch.

 

Compliance and documentation

This grade is declared RoHS. Across the wider range we work to RoHS, REACH, PAHs, FDA and BPA requirements, and we will confirm the status of a specific regulation for your market on request.

A certificate of analysis goes out with every batch, and the SDS and full TDS are available before you order. If your project names a standard,

send it over and we will tell you plainly whether WM72 meets it or whether you need a different grade.

 

Frequently asked questions

 

What dosage do I need for cable jacketing?

Most PE jacket specifications target 2.5% carbon black in the finished compound. WM72 carries 36%, so 2.5 ÷ 0.36 lands at about 7%.

That puts the practical working range at 6–8%, and you should confirm the exact figure on a trial run with your own resin.

Can I run it in PP as well as PE?

Yes, in both. That is what makes it a general-purpose grade. The carrier is PE, so on a PP line give the screw enough mixing length and check the surface on the first few metres.

How is dispersion graded?

We grade dispersion on a visual scale where a lower number is better, and WM72 is supplied at ≤3. Jacket specifications commonly call for ≤3 on a comparable scale.

If your project names a tighter figure, send it over and we will confirm before you commit to a trial.

Will it change the mechanical properties of my part?

The effect is small. The carrier is clean PE with the pigment already dispersed in it, so tensile strength and elongation of the base resin are largely retained. Confirm on your own formulation, as always.

Can I use it for XLPE or LV insulation?

No. Insulation is a different requirement. It needs controlled electrical properties and an additive package built for the crosslinking route you use. WM72 is for the jacket.

We supply insulation-grade compounds separately, so tell us what you are building.

Do you supply samples and OEM grades?

Yes to both. OEM is accepted: we can adjust carbon black loading and carrier to your specification, and we keep your formulation confidential. Samples ship with a certificate of analysis.

Packaging and storage

Supplied in 25 kg bags, PE or composite paper. Store dry, enclosed and out of direct sunlight. Reseal the bag after opening so the product stays dry.

Send us the part, the resin and the black you need

 

Tell us the jacket wall thickness, the base resin and your target carbon black level, and we will come back with a dosage and a sample.

If you already have a rejected batch from another supplier, send a photo with it.

 

Packing and Storage 

25kg/bag, PE or Composite Paper bag

Stored under dry, enclosed and cool conditions, protected from UV rays and/or direct sunlight. After used, the opened packaging must be resealed properly to prevent the product from absorbing moisture, which could affect its performance.

 

Note 

The technical results are typical values and are provided for customer reference only. They are not to be regarded as a guarantee of minimum or maximum quality specifications.

 


Previous: No more data

Related Products
black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

black-masterbatch-blown-film-extrusion-1010C

Environmentally Friendly Black Masterbatch WM101-WM101

Environmentally Friendly Black Masterbatch WM101

Introduction WM101 is produced by polymer additive with pre-dispersed carbon black , then compounded with the basic resin through plastication. It is widely used in injection, pipe, blow film applications. It features low dosage, high blackness, goo...

black masterbatch for general use

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E-WM8E

High Concentration Environmentally Friendly Filled Black Masterbatch WM8E

Introduction WM8E is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and injection applications. Suitable for PP and PE...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Universal Courier bag Extrusion Black Masterbatch WM2ADM-WM2ADM

Universal Courier bag Extrusion Black Masterbatch WM2ADM

Introduction WM2ADM is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing , blowing plastic and fiber applications. Suitable for PP and PE m...

black-masterbatch-mulch-blown-film-extrusion-26-DM002

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1-WMULCH-1

Stable Dispersion & Excellent Hiding Concentrated Mulch Black Masterbatch WMULCH-1

Introduction Mulch film is judged in the field, not in the warehouse. By the time a roll reaches the bed former, three things have already decided how the film will behave for the rest of the season: how much carbon black is genuinely in the film, ...

black masterbatch

High Concentration Carrier-Free Black Masterbatch WMB34-WMB34

High Concentration Carrier-Free Black Masterbatch WMB34

Introduction WMB34 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE ABS PA+GF...

black masterbatch

Strong And High Pigment Black Masterbatch WM913-WM913

Strong And High Pigment Black Masterbatch WM913

Introduction WM913 is produced by pre-dispersed carbon black with polymer additive, then compounded through plastication. It is widely used in modified compounding applications. Suitable for PP PE ABS PPR ABS HIPS materials. It features low dosage...

black masterbatch for injection

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11-WMEG11

BPA Free & Low Volatile Environmentally Friendly Interior Black Masterbatch WMEG11

Introduction WMEG11 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materi...

black masterbatch for automotive parts

BPA Free & LFGB Approved food grade Black Masterbatch WMB56-WMB56

BPA Free & LFGB Approved food grade Black Masterbatch WMB56

Introduction WMB56, a low-odour black masterbatch for ABS, AS and PC appliance housings WMB56 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in inje...

black-masterbatch-PP-superior-blueblack-modified-engineering-compounding-TKB2025007(8)-5D

Strong And High Pigment PP Black Masterbatch WM785D-WM785D

Strong And High Pigment PP Black Masterbatch WM785D

Introduction WM785D is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in modified compounding and injection applications. Suitable for PP and PE materia...

black-masterbatch-home-appliance-casing-BPA-free-lfgb-approved-2016HC

Injection Molding Reinforced Black Masterbatch WM16H (UN2014) -WM16H

Injection Molding Reinforced Black Masterbatch WM16H (UN2014)

Introduction WM16H is produced by pre-dispered carbon black, and then compounded with basic resin. It is widely used in ABS, PC/AS high glossy injection and modifiled compounding applications. Suitable for PP PE PC/ABS GPPS POM GPPS PA+GF materials....

black masterbatch high concentration

Structure-Enhanced SAN Black Masterbatch WM2A-WM2A

Structure-Enhanced SAN Black Masterbatch WM2A

Introduction WM2A is produced by high-pigment carbon black with AS as carrier and special dispersion agent. Its carbon black is stable and blue-shape grade. Suitable for ABS PC high glossy injection materials, also PPO PPS PA PET etc. thermoplasti...

black-masterbatch-PS-panel-extrusion-KB2506026

Structure-Enhanced PS Black Masterbatch WM626-WM626

Structure-Enhanced PS Black Masterbatch WM626

Introduction WM626 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and injection applications. Suitable for HIPS materials. It features lo...

black-masterbatch-PC-modified-engineering-compounding-KB2506024-5

Structure-Enhanced PC Black Masterbatch WM6245-WM6245

Structure-Enhanced PC Black Masterbatch WM6245

Introduction WM6245 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in extrusion and high glossy injection applications. Suitable for PC ABS/PC materia...

black masterbatch for injection

Universal Environmentally Resistant Black Masterbatch WM72-WM72

Universal Environmentally Resistant Black Masterbatch WM72

Introduction WM72 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in film blowing and injection applications. Suitable for PP and PE materials. It fea...

black masterbatch for food grade 2070E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2-WM70E2

Environmentally Friendly FDA approved & food grade Black Masterbatch WM70E2

Introduction WM70E2 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection (both general and thin wall injection), blow molding and extrusion sh...

black-masterbatch-blown-film-extrusion-ZYF26-001

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF-WM261YF

Low Volatile & High Concentration Environmentally Friendly Filled Black Masterbatch WM261YF

Introduction WM261YF is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection and modified compounding applications. Suitable for PP PE materials....

black-masterbatch-water-pipe-extrusion-GS001-5

Environmentally Resistant Black Masterbatch WM3F-WM3F

Environmentally Resistant Black Masterbatch WM3F

Introduction WM3F is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in water supply pipe,drip irrigation pipe,corrugated pipe and film blowing applicati...

black masterbatch for injection

General Low Carbon Black Masterbatch WME1-WME1

General Low Carbon Black Masterbatch WME1

Introduction WME1 is produced by unique process in which carbon black is pre-dispersed, then compounded with the polymer additive through plastication. It is widely used in injection, extrusion pipe and blow film applications. It features low dosage...

black-masterbatch-sewer-pipe-extrusion-A307-3

Weather-Resistant Black Filler Masterbatch WM307-WM307

Weather-Resistant Black Filler Masterbatch WM307

Introduction WM307 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, blow film and compounding applications. Suitable for PP, PE material...

black masterbatch for blown film

Durable Black Environmentally Friendly Functional Masterbatch WM30-WM30

Durable Black Environmentally Friendly Functional Masterbatch WM30

Introduction WM30 is produced by unique process in which carbon black is pre-dispersed, then compounded with the basic resin through plastication. It is widely used in injection, modified compounding, pipe & sheet applications. Suitable for PP ,PE a...

Get Your Free Sample Now
Submit this form and our sales representative will contact you soon.
*Name
Phone
*Email
Company
*Message